How to Calculate Rack Load Capacity

Your rack's rating only protects you if you read it the right way.

Every rack has a limit, and going over it puts people and products at risk. The number on the label is a starting point, not the full story: how the weight sits on the level, how long the beams are, and how hard the pallets land all change what your rack can safely hold. Here are four checks to run before you load.

1. Know your UDL

Rack ratings assume a Uniformly Distributed Load (UDL). That means the weight is spread evenly across the level, not piled in one spot. A pallet concentrated in the middle of a beam stresses it far more than the same weight spread end to end.

Also check how the rating is written. Beam capacities are listed per pair of beams, not per beam, so the number covers the whole level.

For cantilever racks, divide the weight on a level by the number of arms holding it. A 3,000 lb load on three arms needs arms rated for at least 1,000 lbs each.

2. Longer beams hold less

The longer the span, the less weight a beam can carry. A Unirak beam pair holds 3,385 lbs at 96" but only 1,505 lbs at 144". That's less than half the capacity for 48 extra inches.

The same idea applies vertically. Wider spacing between beam levels lowers how much weight your uprights can carry. If you're adding height between levels to fit taller loads, recheck your upright capacity too.

3. Watch the sag

All steel bends a little under load, and that's normal. The rule of thumb is that a beam shouldn't sag more than its length divided by 180. 

On a 96" beam, that's about 1/2". Measure at the center of the beam while it's loaded. One more check: if a beam stays bent after you unload it, it's been overstressed. Stop using it and replace it.

4. Build in a buffer

Size your beams for your heaviest pallet, not your average one. Then allow about 25% extra for shock load, the added force when a forklift sets a pallet down harder than planned. 

For example, if your heaviest level holds 4,000 lbs, look for a beam pair rated for at least 5,000 lbs. Pallet Rack Step Beams are rated from 3,385 to 9,135 lbs per pair, so there's room to size up.

Load with confidence

A safe rack comes down to four numbers: an evenly spread load, the right beam length, sag within limits, and a 25% buffer. Check them before you load, and you protect both your people and your product. 

Ready to plan your setup? Design your rack with the 3D Pallet Rack Builder >

Frequently asked questions

What does UDL mean on a rack rating?

UDL stands for Uniformly Distributed Load. It means the rated capacity assumes weight is spread evenly across the whole level, not concentrated in one spot.

Is beam capacity listed per beam or per pair?

Beam capacities are listed per pair of beams. The rating covers the full level that the two beams support together.

How do I calculate load capacity for cantilever arms?

Divide the weight on a level by the number of arms holding it. A 3,000 lb load on three arms needs arms rated for at least 1,000 lbs each.

Why do longer beams hold less weight?

A longer span bends more under the same load, so its rated capacity drops. A Unirak SB350 beam pair holds 3,385 lbs at 96" but only 1,505 lbs at 144".

How much beam sag is acceptable?

A loaded beam shouldn't sag more than its length divided by 180. On a 96" beam, that's about ½". If a beam stays bent after unloading, stop using it.

How much safety margin should I add to my rack capacity?

Size beams for your heaviest pallet, then add about 25% extra for shock load. For a 4,000 lb level, choose a beam pair rated for at least 5,000 lbs.

Stay in touch

The latest news & helpful info. Sign up and never miss an update.